Last reviewed: November 9, 2026. Formulas checked against standard industry conversions. How we calculate.
Quick answer: A 10-foot long, 2-foot high wall built with 16×6 inch blocks needs 8 blocks per course, 4 courses, 32 blocks in total, 36 blocks with 10% waste, and 8 cap blocks. Use this retaining wall block calculator to work out blocks, courses, waste, and caps for your wall.
Retaining Wall Block Calculator
Enter your measurements below. Results update when you change a value, or press Calculate.
Blocks per course:
Number of courses:
Total blocks:
Total blocks with 10% waste:
Cap blocks:
Estimates are for planning. Check the block manufacturer’s instructions and local rules for walls over 4 feet high.
How the Retaining Wall Block Calculator Works
This retaining wall block calculator counts blocks in two steps: blocks across, then courses up. Blocks per course equals wall length in inches divided by block length in inches, rounded up. Courses equals wall height in inches divided by block height in inches, rounded up. Multiply those two numbers for total blocks, then add 10% waste and round up again. Cap blocks equal blocks per course, because the top course gets one cap per block.
- Measure wall length in feet along the face of the wall. For a stepped or curved wall, measure in sections and calculate each section separately.
- Measure wall height in feet from the base to the top of the last full course, not including caps.
- Choose your block size. The 16×6 inch block is the default, with 12×4 inch and 18×6 inch options. Check the actual block dimensions, because nominal sizes can differ slightly.
- Order the waste figure. The 10% allowance covers cuts, breakages, and partial blocks at the ends.
Worked Example: 10 Feet by 2 Feet, 16×6 Inch Blocks
Length: 10 feet is 120 inches, divided by 16 inches gives 7.5, rounded up to 8 blocks per course. Height: 2 feet is 24 inches, divided by 6 inches gives 4 courses. Total: 8 multiplied by 4 is 32 blocks. With waste: 32 multiplied by 1.10 is 35.2, rounded up to 36 blocks. Caps: one per block in the top course, so 8 cap blocks.
Base Gravel Note
Build the wall on a compacted gravel base about 4 to 6 inches deep, and bury the first course about halfway for stability. The block count above does not include base material, so work out gravel separately with the Gravel Calculator. For drainage, check the block manufacturer’s guidance on backfill and drainage pipe, and for walls over 4 feet high, or walls holding up a driveway or slope, get professional engineering advice. Browse all of our tools from All Calculators.
Frequently Asked Questions
How many blocks do I need for a 10×2 foot retaining wall?
With 16×6 inch blocks, 8 blocks per course and 4 courses gives 32 blocks, or 36 blocks with 10% waste, plus 8 cap blocks. That is the hand-check example at the top of this page.
What is a course in a retaining wall?
One horizontal row of blocks. The first course sits on the compacted gravel base, half-buried, and each course above it is stacked and offset so joints do not line up.
Do I need cap blocks?
Cap blocks finish the top of the wall, give a clean edge, and help hold the top course together. You need one cap per block in the top course, so the cap count equals blocks per course.
How much gravel do I need for the base?
Plan for a compacted base 4 to 6 inches deep under the wall, plus drainage backfill behind it. Use the Gravel Calculator for the base volume, and follow the block manufacturer’s drainage guidance.
Do I need an engineer for a tall retaining wall?
For walls over 4 feet high, walls holding up a driveway, or walls on a slope, get professional engineering advice and check local rules before building. This calculator only counts blocks; it does not check structural design.
Related Calculators
Use this retaining wall calculator for block walls whenever you need a quick block count before ordering materials.
Related calculators
Plan the whole project with the retaining wall calculator, the paver calculator, and the dirt calculator for backfill.
Retaining Wall Block FAQs
How many retaining wall blocks do I need?
Divide the wall length by the block length to get the blocks per course, then divide the wall height by the block height to get the number of courses, and multiply the two together. A 16 ft long, 2 ft high wall built with 24 in × 6 in blocks needs 8 blocks per course and 4 courses — 32 blocks in total. Add 10% for cuts and spares, so order 36. The calculator above works this out for your wall and your block size.
How many cap blocks do I need for a retaining wall?
You need one cap block for every block in the top course, because the caps run in a single row along the top of the wall. The 16 ft example wall above needs 8 cap blocks. Add one or two spares if your wall has corners or you expect angled cuts at the ends.
How much gravel do I need behind a retaining wall?
Plan on a drainage zone of clean, angular gravel at least 12 inches wide behind the wall, running the full height of the wall, plus a compacted gravel base under the first course. That backfill lets water drain to the base instead of pushing against the blocks. Work out the volume with the gravel calculator: length × height × 1 ft depth gives you the drainage zone.
How deep should the base be for a retaining wall?
Dig the base trench deep enough for 4 to 6 inches of compacted gravel plus the buried part of the first course. A common rule is to bury about 1 inch of the wall’s height for every 8 inches of height above ground, so a 2 ft wall sits on roughly 3 inches of buried block below grade. The base should extend about 6 inches in front of and behind the first course. Angular crushed stone compacts tighter than round gravel and makes the better base.
Do I need landscape fabric behind a retaining wall?
Yes — line the back of the drainage gravel with landscape fabric where it meets the soil. The fabric stops fine soil washing into the gravel and clogging the drainage zone, which is one of the main reasons segmental block walls lean or bulge over time. Overlap fabric seams by at least 12 inches.
How high can I build a retaining wall without an engineer?
Most segmental block walls up to about 3 to 4 feet of exposed height are suitable for DIY building, following the block manufacturer’s instructions. Taller walls, walls holding a slope or a driveway, and walls on soft soil usually need geogrid reinforcement and may need a permit or an engineer’s design — check your local rules before you build.