Last reviewed: November 9, 2026. Formulas checked against standard industry conversions. How we calculate.
Asphalt Calculator
Use this free asphalt calculator — also a pavement calculator — to estimate how many tons of asphalt (blacktop) you need for a driveway, parking area or road patch. Enter the length, width and thickness, add a small waste allowance, and get an instant estimate in tons and cubic yards, with an optional cost estimate.
Asphalt Calculator
Enter your measurements below. Results update when you change a value, or press Calculate.
TONS OF ASPHALT NEEDED
–
CUBIC YARDS (VOLUME EQUIVALENT)
–
ESTIMATED COST
$0.00
Enter a length, width and thickness to see your estimate.
How the Asphalt Calculator Works
Asphalt is usually ordered by weight, in tons, rather than by volume. This calculator uses the common industry rule of 110 lb of asphalt per square yard per inch of thickness. First it converts the area to square yards by dividing the square footage by 9. Then it multiplies square yards by thickness in inches and by 110 lb to get the total weight in pounds, divides by 2,000 to get tons, and finally applies the waste allowance you selected. Cubic yards are calculated separately from the volume: length times width times thickness in feet, divided by 27.
Worked example: a 10 x 20 ft area at 2 in thick, with 0% waste, is 200 sq ft, or 22.22 sq yd. Multiplying 22.22 x 2 x 110 gives 4,889 lb, which is 2.44 tons. At 3 in thick, with 0% waste, the same area needs 3.67 tons (22.22 x 3 x 110 = 7,333 lb). At 5% waste, the 3 in case needs 3.85 tons.
How Thick Should Asphalt Be?
Thickness depends on what the surface will carry and what is underneath it. Use the typical guidance below as a starting point, and check local codes and your contractor’s advice for your soil and project.
| Project | Typical asphalt thickness | Notes |
|---|---|---|
| Resurfacing / overlay | 1.5-2 in | A new surface layer over a sound existing base. |
| Residential driveway (new) | 2-3 in surface | Over a compacted gravel base, often 4-6 in of total structure. |
| Heavy vehicles / commercial | 3-4 in or more | Thicker surface and a stronger base for heavier loads. |
These are typical values only. The right thickness varies with soil, drainage, traffic and local codes.
Asphalt Coverage per Ton
Using the same 110 lb rule, 1 ton of asphalt covers about 82 sq ft at 2 in thick, about 55 sq ft at 3 in thick, and about 41 sq ft at 4 in thick. The calculation is 2,000 lb divided by (110 x thickness) square yards, multiplied by 9 to convert square yards to square feet. Thicker layers use more material per square foot, so coverage per ton falls as thickness rises.
Driveway example: a typical 12 x 50 ft driveway at 3 in thick needs about 11 tons. That area is 600 sq ft, or 66.67 sq yd, and 66.67 x 3 x 110 = 22,000 lb, which is 11 tons before any waste allowance.
Asphalt Calculator FAQs
How many tons of asphalt do I need for a driveway?
A typical 12 x 50 ft driveway at 3 in thick needs about 11 tons before waste. To estimate your own driveway, multiply square yards by thickness in inches and by 110 lb, divide by 2,000 to get tons, then add your waste allowance.
How much does a ton of asphalt cover?
About 82 sq ft at 2 in thick, about 55 sq ft at 3 in thick, and about 41 sq ft at 4 in thick. Coverage falls as thickness rises because each square foot needs more material.
What is the difference between asphalt and blacktop?
They are the same material family. Blacktop is a mix with smaller aggregate, common for driveways, and both are estimated the same way here.
How much does asphalt cost per ton?
Hot-mix material often runs roughly $40-$80 per ton before delivery and installation, while installed driveway paving commonly costs several dollars per square foot. Prices vary widely by region, mix and project size, so get local quotes for a firm price.
Can I use this as a paving cost estimator?
Yes. Enter the price per ton to estimate material cost. Installed cost adds base preparation, labour and equipment, so a material-only estimate will be lower than a full installed quote.
Related Calculators
Related calculators
For a gravel driveway, try the driveway gravel calculator.
Asphalt Price per Ton
Hot-mix asphalt typically costs $40 to $80 per ton for the material itself, picked up at the plant or priced into a delivered load before installation. That is the figure to enter in the calculator above when you want a material-only estimate. Blacktop is priced the same way — it is the same material family with a finer aggregate mix, so a ton of blacktop costs the same as a ton of asphalt in most markets.
What moves the price per ton:
- Delivery distance — hot mix has to travel in heated trucks and be laid while hot, so plants charge more per ton the farther the job is from the plant.
- Order size — a full truckload prices far better per ton than a small partial load.
- Mix type — finer surface-course mixes usually cost more per ton than coarse base-course mixes.
- Oil prices and region — bitumen is a petroleum product, so plant prices follow oil markets and vary widely by area.
Worked example: a 20 ft × 20 ft driveway at 3 inches thick needs about 7.3 tons of asphalt. At $40 to $80 per ton the material runs roughly $290 to $590 — the rest of an installed quote is base preparation, labour and equipment, which is why installed paving is priced per square foot instead. Bagged cold patch is the expensive way to buy asphalt (the equivalent of several hundred dollars per ton) and only makes sense for small repairs.