Start calculating

Rebar Calculator

Last reviewed: November 2, 2026. Formulas checked against standard industry conversions. How we calculate.

Use this free rebar calculator, also a rebar calculator for slab work, to work out how many bars you need for a concrete slab, how many feet of rebar to buy, and how much it weighs. Enter your slab size, spacing, bar size, stock length, and laps and waste allowance, and get an instant estimate.

Rebar Calculator

Enter your slab measurements below. Results update when you change a value, or press Calculate.

Bars along the length: –

Bars along the width: –

Total linear feet: –

Bars to buy: –

Total weight: –

Method: For each direction, spaces equals the dimension in inches divided by the spacing, rounded up, and bars equals spaces plus 1. Total linear feet equals bars along the length times slab length plus bars along the width times slab width, using the full dimensions with no edge inset. Bars to buy equals total linear feet times 1 plus the waste percentage, divided by the stock length, rounded up. Weight equals total linear feet times the pounds per foot for the chosen bar.

Estimates are for planning. Check local code and your slab design before ordering.

How to Calculate Rebar for a Slab

The grid method used by the tool above is straightforward. Work through one direction at a time, then add the two directions together.

  1. Measure the slab length and width in feet, then convert each dimension to inches by multiplying by 12.
  2. For the bars that run along the length, divide the slab width in inches by the spacing in inches, round up to a whole number of spaces, and add 1 bar. That extra bar closes the grid at the far edge.
  3. For the bars that run along the width, divide the slab length in inches by the spacing in inches, round up, and add 1 bar.
  4. Multiply the bars along the length by the slab length, and the bars along the width by the slab width, then add the two results. That gives total linear feet, using the full slab dimensions with no edge inset.
  5. For bars to buy, add your laps and waste percentage to total linear feet, divide by the stock bar length, and round up to a whole bar.
  6. For weight, multiply total linear feet by the pounds per foot for the chosen bar size.

Worked example: a 10 by 10 ft slab at 12 in spacing has 11 bars each way, so 11 times 10 ft plus 11 times 10 ft equals 220 linear feet. With #4 bar at 0.668 lb per ft, that is 147 lb.

Rebar Spacing Guide

Spacing sets how tight the grid is. Tighter spacing gives more steel and a stiffer slab, but it also costs more and takes longer to tie.

  • Patio and walkway slabs: 12 to 24 in spacing is typical for light loads.
  • Driveways: 12 to 18 in spacing is typical.
  • Heavier loads: use tighter spacing, and check the slab design for the load it must carry.

Local code governs. Where a slab is structural, or where local rules set a minimum, follow the code and the approved design, not this guide alone.

Rebar Bar Size Table

Bar sizeDiameterWeight per footTypical uses
#33/8 in0.376 lb per ftLight patios, walkways, and small slabs
#41/2 in0.668 lb per ftMost home slabs, patios, and driveways
#55/8 in1.043 lb per ftHeavier slabs, driveways with heavy vehicles, and structural work

Keep rebar mid-slab on chairs or dobies, not on the ground, so concrete surrounds the steel. Where bars join end to end, lap them at least 24 to 30 diameters as typical practice. For #4 bar, that is 12 to 15 in. Local code governs lap length.

Frequently Asked Questions

How much rebar do I need for a 20×20 slab?

At a 12 in grid, a 20 by 20 ft slab needs 21 bars each way, for 840 linear feet in total. Add laps and waste, then divide by your stock bar length and round up to find bars to buy.

Rebar or wire mesh — which is better for a slab?

Rebar is usually better for driveways, larger slabs, and heavier loads, because it is stronger and holds its position better during a pour. Wire mesh suits light patios and walkways and is easier to handle, but it must stay mid-slab to do its job. For a structural slab, follow local code and the approved design.

What spacing should I use for rebar in a slab?

Twelve inches is a common starting point for a home slab. Patios and walkways often use 12 to 24 in, driveways often use 12 to 18 in, and heavier loads need tighter spacing. Local code governs.

How much does rebar weigh per foot?

#3 bar weighs 0.376 lb per ft, #4 bar weighs 0.668 lb per ft, and #5 bar weighs 1.043 lb per ft. Multiply total linear feet by the weight for your bar size to get total weight.

Related Calculators

Related calculators

For fence footings, try the fence post concrete calculator.

Ready to calculate?

Start with your measurements and get a material estimate in seconds.

Explore all calculators