Start calculating

Fence Post Concrete Calculator

Last reviewed: November 2, 2026. Formulas checked against standard industry conversions. How we calculate.

Fence Post Concrete Calculator

Find out how much concrete you need to set fence posts, in cubic feet and bags per post and for the whole fence. Enter your post size, hole size and the number of posts.

Post Concrete Gravel base Hole depth
Concrete = hole volume − post volume
A 4×4 post is 3.5 in. A 6×6 is 5.5 in.
A common rule is about 3 times the post width.
Often one third of the post length, and below the frost line in cold areas.
Set to 0 for no gravel.

Your estimate

Planning estimate only. Bag yields vary by brand, so check the yield on the bag. Hole size and depth depend on your fence height, soil, frost depth and local code. Gate and corner posts usually need bigger holes, so calculate them separately.

How the fence post concrete calculator works

ExactYard works out the volume of the hole around the post, subtracts the space the post takes up, and leaves room for the gravel base if you use one. It then adds your waste allowance and divides by the bag yield.

Hole area      = π × (Hole diameter ÷ 2)²
Post area      = Width² (square)  or  π × (Diameter ÷ 2)² (round)
Concrete depth = Hole depth − Gravel depth
Per post       = (Hole area − Post area) × Concrete depth
Total          = Per post × Posts × (1 + Waste ÷ 100)
Bags           = CEILING(Total ÷ Bag yield)

Fence post concrete FAQ

How much concrete do I need per fence post?

A 4×4 post in a 10 inch wide hole, 30 inches deep with a 4 inch gravel base, needs about 1 cubic foot of concrete. That is roughly 1.7 bags of 80 lb mix. Ten such posts need about 19 bags with 10 percent extra.

How many 80 lb bags of concrete per post?

An 80 lb bag yields about 0.6 cubic feet, so most standard 4×4 posts use between 1.5 and 2 bags. Larger holes or deeper posts use more.

How wide should a fence post hole be?

A common rule is a hole about three times the width of the post, so around 10 to 12 inches for a 4×4. Gate and corner posts often get a wider hole.

How deep should a fence post hole be?

Often at least one third of the post’s total length, and deeper in places where the ground freezes. Check your local frost depth and building guidance.

Do I need gravel under a fence post?

Many installers put 4 to 6 inches of gravel in the bottom so water drains away from the end of the post. It also reduces the concrete you need.

Should I order bags or ready-mix?

Bags suit a few posts. For a long fence needing around a cubic yard or more, ready-mix may be cheaper, but delivery to a narrow fence line can be hard, so many people still use bags.

Related Calculators and Guides

Setting a fence? These tools and guides cover the rest of the job:

Related calculators: for reinforcement in larger pours, try the rebar calculator.

How Deep Should a Fence Post Be?

As a rule, bury about one-third of the post, with a minimum of 24 inches in the ground, and set the post below the local frost line. In cold climates the frost line can be deeper than the one-third rule, so the deeper of the two depths governs. The chart below gives a practical starting point for a standard fence in normal soil.

Fence heightPost lengthHole depth
4 ft fence8 ft post24-30 in
5 ft fence8 ft post30 in
6 ft fence8-10 ft post32-36 in
7 ft fence10 ft post36 in
8 ft fence10-12 ft post40-48 in

For example, a 6 ft fence on an 8-10 ft post needs a 32-36 in hole, which leaves 6 ft above ground with enough post buried for stability. A taller fence catches more wind, so it needs a deeper hole and, in many cases, a longer post. Always check the local frost depth before digging, and add depth where frost, soft soil or high wind makes the standard depth insufficient.

Fence Post Spacing

Fence posts are typically 6-8 ft apart, measured from the centre of one post to the centre of the next. Closer spacing, toward 6 ft, suits heavier panels, taller fences and windy sites, while 8 ft spacing suits lighter fencing in sheltered ground. Use the spacing together with the hole depth above to work out how many posts and how much concrete the fence needs.

Ready to calculate?

Start with your measurements and get a material estimate in seconds.

Explore all calculators